Description: microprocessor electronic board system to control and monitor electrical and electronic units for passenger and goods lifts. Control and monitor serial communication between car and control unit.
micro beta boards
products | electrical system | micro beta boards
External 1B (control unit) dimension:
- Length – 247mm
- Width – 147mm
- Height – 35mm
External 1C (car) dimensions:
- Length – 203mm
- Width – 114mm
- Heigth – 30mm
Fixing: the boards are equipped with up to 6 holes at the corners and in the middle (only for 1B) for fixing by screw and spacer to the control unit chassis.
Power supply:
- Power supply voltage: 18Vdc straightened (+/-15%) or 24V levelled.
- Operating voltage: 48Vcc.
- Indicator lights voltage: 24Vdc Com +
- Set of safeties monitoring inputs: 48Vdc optically isolated (compliant with European norms EN81).
- Movement control outputs: relay tipe, insulated contact max 6A-48Vdc (compliant with European norms EN81).
- Operating temperature: -5° to +40° C (23° to 104° F)
Tipes fo systems:
- Hydraulic: Direct start-up, Star-delta, soft-start, soft-stop, 2 speed.
- Electric: VVVF, 2 speed.
Floors: Serial transmission, standard up to 8 stops/services. Expandible in multiplpes of 8 stops.
Operations:
- Universal (expandible in multiple of 8 stops).
- Collective selective down (expandible in multiple of 8 stops).
- Collective selective up-down (standard up to 5 stops/services, expandible in multiple of 4 stops).
- Simplex – Duplex (collective down, collective complete).
Doors:
- Manual on floors/car
- Manual on floors/without car-with safety photocell (only goods lift).
- Automatic, up to 3 doors with alternate, simultaneous or 2 selective opening.
- Photocell, safety cam, open/close push-button, doors stationary when open/close.
Miscellaneous controls: no phase/phase sequence control, 2 electronic motor cut-out, max. pressure monitoring devices, oil temperature monitoring device, travel time, delay 15′, stationary on main floor, reserved/preferential operations, fire service/fire fighting operations, full load, overload.
Indicator lights: available/in use (steady/flashing), arrival, car/floor call accepted, binary-decimal-1/N display position, direction arrows/next direction selective at floor, overload, GONG.
Shaft monitoring device: standard with pulse sensors, normal/short floor monitoring devices.
Emergency: alarm, emergency light 12V, prepared for downhill in the event of a power cut, for hydraulic systems return to the lowest floor and door opening, for electric return to the nearest floor and door opening and displacement maneuver only with Gearless.
*Programmer PROG2: supplied on request, used for system parameters programming and reading system errors.
* OPTION
Our products are certified in compliance with European Norms EN81.
Compliance with different Norms on request.
Product brochure
Description: microprocessor electronic board system to control and monitor electrical and electronic units for Hydraulic and Electric lift platforms. Control and monitor serial communication between car and control unit.
External 1K (control unit) dimension:
- Length – 165mm
- Width – 160mm
- Height – 30mm
Fixing: the boards are equipped with up to 6 holes at the corners for fixing by screw and spacer to the control unit chassis.
Power supply:
- Power supply voltage: 18Vdc ( 24V levelled).
- Operating voltage: 24Vdc.
- Indicator lights voltage: binary/decimal display, direction arrows, = 24Vdc – Common +. In use signal, GONG, excessive load = 24Vdc – Common -.
- Set of safeties monitoring inputs: 24Vdc optically isolated (compliant with European norms EN81).
- Movement control outputs: relay tipe, insulated contact max 6A-24Vdc (compliant with European norms EN81).
- Operating temperature: -5° to +40° C (23° to 104° F)
Tipes fo systems:
- Hydraulic: Direct start-up, 1 or 2 speed.
- Electric: VVVF.
Floors: Serial transmission, standard up to 4 stops/services. *Up to 6 floors with expansion (1F board).
Operations: man present, universal.
Doors:
- Manual on floors/car
- Manual on floors/without car-with safety photocell (only goods lift).
- *Automatic, up to 2 doors with alternate, simultaneous or selective opening.
- Photocell, safety cam, open/close push-button, doors stationary when open/close.
Miscellaneous controls: 2 electronic motor cut-out, max. pressure monitoring devices, oil temperature monitoring device, travel time, delay 15′ (universal operation), stationary on main floor, full load, overload.
Indicator lights: available/in use (steady/flashing), *binary-decimal display position, *direction arrows, overload, GONG.
Shaft monitoring device: standard with pulse sensors.
Emergency: alarm, emergency light 12V, prepared for downhill in the event of a power cut for hydraulic systems return to the lowest floor .
*Programmer PROG2: supplied on request, used for system parameters programming and reading system errors.
* OPTION
Our products are certified in compliance with European Norms EN81.
Compliance with different Norms on request.
Product brochure